Spindle VFD Selection and Tuning: Power, Cable and Parameter Setup
Key Takeaway
Spindle vfd selection is a three-number calculation from the motor nameplate, and the tuning is a parameter setup rather than a knob-twiddling exercise. Size the drive for the current at rated load, run the motor with shielded cable and a short earth strap, and set the VFD for the motor’s actual volts, hertz and current before anything else.
Figure 1: The four blocks of a spindle VFD installation: sizing, cabling, parameters and tuning
1. The Four Decisions in a Spindle VFD Installation
A spindle drive is a three-number calculation followed by four decisions, and the second half of the work is where the faults come from. This guide works through the sizing arithmetic from the motor nameplate, the cabling and earthing rules that decide whether the installation works at all, the parameter set that has to be entered before anything else, and a tuning sequence with the current readings that separate a tool problem from a drive problem. The sections are written for a shop doing the work in a real cabinet in a real summer.
A spindle VFD installation is four separate engineering problems, and most of the faults that get blamed on the drive are actually in one of the other three.
Sizing. Which drive, and is it big enough.
Cabling and grounding. How the power and signal travel, and how the machine is earthed.
Parameters. Telling the drive what motor it is driving.
Tuning. Making it behave under real cutting load.
The order matters: an unsized drive cannot be tuned, an unnamed motor cannot be parameterised, and bad cabling makes tuning impossible because the fault looks like a tuning fault.
Section summary. Spindle vfd selection is really four decisions stacked on top of each other: which drive, how it is cabled and earthed, what the drive is told about the motor, and how it is tuned. The order is not arbitrary. An unsized drive cannot be tuned, an unnamed motor cannot be parameterised, and bad cabling makes tuning impossible because the fault presents as a tuning fault. Getting spindle vfd selection right is a matter of respecting that sequence.
The drive in a spindle vfd selection is also the biggest single electrical load in the cabinet, and it sets the incoming supply requirement.
2. Sizing: The Three Numbers on the Nameplate
The motor nameplate carries everything needed to size the drive. For a typical 7.5 kW, 415 V, three phase, 1440 rpm induction spindle motor:
Nameplate item
Value
Use it for
Rated power
7.5 kW
A sanity check on the drive size, and for the cooling requirement
Rated voltage
415 V, 3 phase
Determines the drive’s input voltage and the cable size
Rated current
13.5 A
The primary drive sizing number
Rated frequency
50 Hz
Base speed calculation
Rated speed
1440 rpm
Base speed and slip
Power factor
0.82
Apparent power calculation
Service factor / duty
S1 or S6
Whether the drive can be rated at the motor’s full current continuously
The kVA calculation
For a three phase system, the apparent power is:
kVA = sqrt(3) x V x I x pf
With the numbers above: kVA = 1.732 x 415 x 13.5 x 0.82 = 1.732 x 415 = 718.8; x 13.5 = 9704 VA; x 0.82 = 7957 VA, so 7.96 kVA. That matches the 7.5 kW nameplate, as it should, since a motor’s kW output is always below its kVA input.
For a single phase supply, kVA = V x I x pf, with no sqrt(3) factor: 220 x 13.5 x 0.82 = 2.44 kVA, which is 3.3 times less apparent power for the same mechanical output. That is why single phase is unsuitable for anything above about 3 kW on a CNC.
Sizing the drive
The rule is simple and the exceptions are rare: the drive’s rated output current must be at least the motor’s rated current, and the drive’s rated output voltage must be at least the motor’s rated voltage.
For the 7.5 kW, 13.5 A motor: a 15 A or 18 A drive. Most manufacturers offer 7.5 kW drives rated at 15 A or 16 A, and the next size up at 22 A or 25 A.
The common mistake is to size the drive on the motor’s kW. A 7.5 kW motor with a 0.82 power factor draws 13.5 A, and a drive rated at 16 A is right, while a 7.5 kW drive rated at only 12.6 A is too small.
Size one step up if the spindle sees heavy intermittent cutting. A drive that is continuously loaded at 90 percent of its rating runs hot and derates. A drive at 70 percent of its rating is comfortable.
Check the motor’s service factor and duty
A spindle motor rated for S1 continuous duty can be run at full rated current all the time. A motor rated S6 (intermittent duty) can be run above its rated current for a limited period. The nameplate service factor tells you how much overload the motor can take, and a spindle drive is the one place where that factor matters, because a dull cutter produces a sudden load spike that a feed axis never sees.
As a working rule, allow the drive to deliver up to 150 percent of the motor’s rated current for 60 seconds. If the drive cannot, the spindle will trip on an overload during a heavy cut rather than simply slowing down.
Speed range
The spindle’s usable speed range is set by the motor’s base speed and by the drive’s frequency range. A 4-pole 1440 rpm motor on a 50 Hz supply has a synchronous speed of 1500 rpm and a base speed of about 1440 rpm. To go above that, the drive must supply a frequency above 50 Hz, and above roughly 55 to 60 Hz the motor’s torque falls, its cooling becomes inadequate, and its bearings run hotter. In practice a 415 V VFD is good to 60 to 70 Hz for a standard motor, giving 1800 to 2100 rpm, which is enough for most cutting work with a gearbox or with a higher base speed motor.
For a spindle that needs 6000 to 8000 rpm, the motor must be a 2-pole design rated for high speed, at 2900 rpm base, and the drive must be a 415 V unit capable of 100 to 120 Hz output. VFDs that can be programmed to 120 Hz output are specific models, and they cost more. Check this before ordering, because it is not a software setting you can change later.
Section summary. The sizing arithmetic is short and the numbers come off the nameplate. For a three phase system kVA = sqrt(3) x V x I x pf, which for a 7.5 kW, 415 V, 13.5 A, 0.82 power factor motor gives 7.96 kVA. The rule that follows is that the drive’s rated output current must be at least the motor’s rated current, and the common mistake is to size on the kW and end up with a drive that is 12.6 A where 16 A is needed.
A spindle vfd selection on a 415 V three phase supply is the normal choice for a CNC spindle in India, and the sizing arithmetic is where that decision is justified.
3. Cabling and Grounding: Where the Faults Actually Come From
On a retrofit, the majority of the mysterious spindle faults are cabling faults. They present as intermittent trips, as the spindle that will not start after the machine has been warm for an hour, or as a machine that trips when the coolant pump starts.
The motor cable
Use a screened motor cable. Not a general-purpose rubber cable. A shielded motor cable with a shield that is a continuous foil or braid, rated for VFD output with a capacitance suitable for a high carrier frequency.
Both ends of the shield must be earthed. This is the case for VFD output cables, where the shield carries the common-mode current that the drive injects into the motor cable. A shield earthed at one end only leaves the other end floating and the common-mode current finds another path.
Keep the shield short at the drive. Use a 360-degree EMC gland rather than a single pigtail to a PE stud. A pigtail connection is measurably worse than a full clamp.
Separation
The VFD output cable is the noisiest cable on the machine. Rules that hold:
Keep the motor cable at least 200 mm from encoder feedback cables and from any signal cable, and never parallel with them for more than a short distance.
If they must cross, cross at right angles, never parallel.
Route the motor cable and the encoder cable in separate trays, and separate them from the cabinet mains wiring.
Do not run the motor cable in the same conduit as the thermocouple or the encoder cable, no matter how convenient it is.
Earth straps
This is where most Indian installations are wrong. The earth strap between the drive and the cabinet is often a 2 m length of 4 mm^2 wire, because that is what was in the box.
Use a short wide braided copper strap, 20 to 25 mm wide, between each drive and the cabinet earth bar. The impedance of a strap is proportional to its length and inversely proportional to its width, so a 0.3 m wide strap has roughly a fifteenth of the impedance of a 2 m wire of the same cross-section. In an installation where the fault is a high-frequency common-mode issue, the impedance of the earth path is what decides whether the noise stays inside the cabinet.
Then the cabinet to the plant earth: one dedicated conductor, as short as possible, sized to the highest earth fault current in the installation. And the cabinet door bonded with a strap, because a door is a hinged conductor and its bond is the first thing to be forgotten.
The motor as a noise source
The motor is part of the circuit. A 415 V motor on a VFD produces bearing currents, which come from the common-mode voltage on the shaft. Two consequences:
Insulated bearings or a shaft earth ring on any spindle above about 5 kW. A shaft earth ring is a carbon brush on the shaft end that grounds the shaft, and it costs very little compared with a bearing failure.
Do not use a standard VFD motor. If the existing spindle motor is an ordinary 415 V motor, add an output reactor between the drive and the motor. An output reactor, typically 2 to 5 percent impedance, reduces the dV/dt at the motor and therefore the bearing current. It also reduces the motor’s noise and the cable’s electromagnetic field, and it costs a small fraction of the drive.
Use the shielded cable and the output reactor rather than lowering the carrier frequency, if the machine can take it. A reactor of 3 to 5 percent impedance also reduces the motor’s dV/dt, which prolongs the motor’s insulation life, and that matters on a retrofit where the original motor cable is 20 years old.
Section summary. A drive that has not been given the motor’s nameplate data will run, badly, and that is the most common cause of a spindle that will not hold speed or trips on overload. The mandatory entries in spindle vfd selection are rated voltage, frequency, current, speed and power, plus a rotating auto-tune with the drive train uncoupled. The symptom of bad slip compensation is a spindle whose real speed changes with the load while the display shows a constant commanded speed.
The earthing and shielding in spindle vfd selection is not paperwork, it is the difference between a machine that runs for ten years and one that is chasing noise faults every month.
5. Tuning on the Machine
With the parameters set, tune in a fixed order and record what you find.
Step 1: no load
Run the spindle through its whole speed range with no load. Listen. A healthy spindle at speed sounds like a smooth hum that rises in pitch with speed. Things to listen for:
A beat or growl at one particular speed. Usually a bearing defect, sometimes the gear mesh if the spindle has a gearbox, and sometimes a resonance of the spindle housing. Note the speed and check whether it occurs at a specific frequency.
A whine that rises and falls. Often the drive, not the spindle.
A change in sound at the top of the speed range. Above base speed, the motor runs into its power-limited region and the sound changes. This is normal, and it is where the motor’s torque is falling away.
Step 2: check the speed accuracy
Command 1000 rpm and check with a tachometer or with the machine’s own spindle feedback if it has any. Then repeat at 2000, 4000 and at maximum. If the commanded speed and the actual speed differ by more than 0.5 percent, the slip compensation is wrong. Re-run the rotating auto-tune.
On a CNC where the control commands the VFD through an analogue 0 to 10 V signal, there is a second scaling step: the controller’s spindle speed is a command in rpm, and the VFD’s analogue reference is a fraction of the maximum frequency. Get the scaling wrong and the spindle runs at the wrong speed with no error message. Test it by commanding 1000 rpm and measuring. The scaling rules and the VFD interface options are in the LinuxCNC hardware guide.
Step 3: load test
Cut a test workpiece in the real material, at the real cutting condition. Watch the current. This is where the diagnostic power of the current reading is.
Step 3: load test
Cut a test workpiece in the real material, at the real cutting condition. Watch the current. This is where the diagnostic power of the current reading is.
Current behaviour
What it means
Steady, low, proportional to the cut
Normal. The spindle is matched to the work.
Steady but high, above 70 percent of rated
The spindle is undersized for the job, or the cut is too aggressive, or the belt or the tool is worn.
Rises steadily during a constant cut
A dull tool. The cutting force is climbing and the motor is loading up. This is the normal way a spindle load behaves.
Spikes at a fixed speed, repeatedly
A mechanical fault. A chipped bearing, a damaged tool, or a chipped cutter tooth passing one per revolution.
Oscillates, hunting
Speed instability. The drive’s slip compensation or its speed loop needs work, or the load is fluctuating.
Drops when the cut starts, recovers
The drive is at its current limit and is doing a slip-and-recover, which is a form of hunting.
Step 4: check the hunting
Hunting is a speed oscillation, and it has three likely causes in order of probability:
Speed loop gains too high. The drive’s speed loop is chasing small load changes. Reduce the speed loop gain, or check that the auto-tune was done correctly.
Mechanical resonance. The spindle or its mounting is resonating. It appears at one speed and disappears elsewhere. Find that speed and check whether it corresponds to the spindle’s natural frequency.
Supply voltage fluctuation. The drive’s DC bus is riding on the supply. Check the supply voltage at the drive under load, and check the input rectifier’s DC bus voltage in the drive diagnostics.
Step 5: the thermal test
Run the spindle at its production cycle for 30 minutes and check the motor’s temperature. The motor’s temperature rise should stay within what the motor’s insulation class allows. A rise of more than 80 degC above ambient indicates the drive is overloading the motor, that the cooling is inadequate, or that the bearings are dragging.
Also measure the spindle’s nose temperature. A spindle that is 20 degC hotter at the nose than at the rear housing is a spindle with a front bearing problem, and that is the finding that justifies a rebuild. The bearing and preload procedure is in the spindle rebuild guide.
Section summary. Tuning is a fixed order and the current reading is the diagnostic instrument most shops never use. The table in spindle vfd selection maps each current behaviour to its cause, and the distinction that matters most is a current that rises steadily during a constant cut, which is a dull tool, against a current that spikes repeatedly at a fixed speed, which is a mechanical fault. Hunting has three causes in order of probability: speed loop gains, mechanical resonance, and supply voltage fluctuation.
The nameplate values in spindle vfd selection have to come off the motor, not out of memory, because the motor on the machine is rarely the motor you planned for.
6. The Mistakes That Cost Time
Using the existing spindle motor with a 220 V single phase supply. It works, and it is marginal. The DC bus at 220 V single phase rectified is about 310 V, and the back-EMF at high speed approaches it, so the spindle loses torque at the top of its range. This is the reason many retrofit spindoles will not hold speed at the top.
Not earthing the cabinet properly. Symptom: the spindle trips or the control resets when the coolant pump or the spindle’s own contactor operates.
Using the motor’s rated frequency as the maximum frequency. The spindle then cannot go above base speed, and the operator complains that the machine is slow.
Skipping the rotating auto-tune. Symptom: the actual speed does not match the commanded speed, and the display shows the commanded value, so the fault is invisible until the operator measures it with a tachometer.
Leaving the factory defaults on the carrier frequency and the acceleration ramp. Symptom: the spindle is noisy and slow, and the noise is blamed on the bearings.
Not writing the parameter values down. Every drive replacement then becomes a guessing exercise, and the tuning is lost. Record the parameters, the auto-tune results and the test dates in the machine’s documentation folder. The full documentation discipline is in the parent retrofit guide, and the pricing of the spindle package is in the CNC retrofit cost calculator.
Section summary. The mistakes in this section are all cheap to avoid and expensive to discover, and they are the ones that get blamed on the wrong component. Using the existing spindle motor on a 220 V single phase supply loses torque at the top of the range, skipping the rotating auto-tune makes the fault invisible until someone measures with a tachometer, and not writing the parameters down turns every drive replacement into a guessing exercise. spindle vfd selection is finished when the values are in the machine’s documentation folder.
The current trend during a cut is the most useful diagnostic in spindle vfd selection, and it costs nothing once the drive is set up to display it.
Size the drive with kVA = sqrt(3) x V x I x pf, and pick the next standard size up from the motor’s full load current.
A 415 V three phase spindle VFD is the normal choice for CNC servos because a 220 V single phase supply leaves no margin for the back-EMF at speed.
Shielded motor cable, bonded at the drive end, with a short wide earth strap from the drive to the cabinet, eliminates most of the mystery faults.
Set the VFD motor nameplate volts, hertz, current, speed and power before any tuning; an unnamed motor makes the drive guess and guess wrong.
Rising current during a cut means the spindle is loaded; a current spike at a fixed speed means a mechanical fault such as a dull cutter or a binding bearing.
Spindle VFD Selection and Tuning: Power, Cable and Parameter Setup
Key Takeaway
Spindle vfd selection is a three-number calculation from the motor nameplate, and the tuning is a parameter setup rather than a knob-twiddling exercise. Size the drive for the current at rated load, run the motor with shielded cable and a short earth strap, and set the VFD for the motor’s actual volts, hertz and current before anything else.
Figure 1: The four blocks of a spindle VFD installation: sizing, cabling, parameters and tuning
1. The Four Decisions in a Spindle VFD Installation
A spindle drive is a three-number calculation followed by four decisions, and the second half of the work is where the faults come from. This guide works through the sizing arithmetic from the motor nameplate, the cabling and earthing rules that decide whether the installation works at all, the parameter set that has to be entered before anything else, and a tuning sequence with the current readings that separate a tool problem from a drive problem. The sections are written for a shop doing the work in a real cabinet in a real summer.
A spindle VFD installation is four separate engineering problems, and most of the faults that get blamed on the drive are actually in one of the other three.
Sizing. Which drive, and is it big enough.
Cabling and grounding. How the power and signal travel, and how the machine is earthed.
Parameters. Telling the drive what motor it is driving.
Tuning. Making it behave under real cutting load.
The order matters: an unsized drive cannot be tuned, an unnamed motor cannot be parameterised, and bad cabling makes tuning impossible because the fault looks like a tuning fault.
Section summary. Spindle vfd selection is really four decisions stacked on top of each other: which drive, how it is cabled and earthed, what the drive is told about the motor, and how it is tuned. The order is not arbitrary. An unsized drive cannot be tuned, an unnamed motor cannot be parameterised, and bad cabling makes tuning impossible because the fault presents as a tuning fault. Getting spindle vfd selection right is a matter of respecting that sequence.
The drive in a spindle vfd selection is also the biggest single electrical load in the cabinet, and it sets the incoming supply requirement.
2. Sizing: The Three Numbers on the Nameplate
The motor nameplate carries everything needed to size the drive. For a typical 7.5 kW, 415 V, three phase, 1440 rpm induction spindle motor:
Nameplate item
Value
Use it for
Rated power
7.5 kW
A sanity check on the drive size, and for the cooling requirement
Rated voltage
415 V, 3 phase
Determines the drive’s input voltage and the cable size
Rated current
13.5 A
The primary drive sizing number
Rated frequency
50 Hz
Base speed calculation
Rated speed
1440 rpm
Base speed and slip
Power factor
0.82
Apparent power calculation
Service factor / duty
S1 or S6
Whether the drive can be rated at the motor’s full current continuously
The kVA calculation
For a three phase system, the apparent power is:
kVA = sqrt(3) x V x I x pf
With the numbers above: kVA = 1.732 x 415 x 13.5 x 0.82 = 1.732 x 415 = 718.8; x 13.5 = 9704 VA; x 0.82 = 7957 VA, so 7.96 kVA. That matches the 7.5 kW nameplate, as it should, since a motor’s kW output is always below its kVA input.
For a single phase supply, kVA = V x I x pf, with no sqrt(3) factor: 220 x 13.5 x 0.82 = 2.44 kVA, which is 3.3 times less apparent power for the same mechanical output. That is why single phase is unsuitable for anything above about 3 kW on a CNC.
Sizing the drive
The rule is simple and the exceptions are rare: the drive’s rated output current must be at least the motor’s rated current, and the drive’s rated output voltage must be at least the motor’s rated voltage.
For the 7.5 kW, 13.5 A motor: a 15 A or 18 A drive. Most manufacturers offer 7.5 kW drives rated at 15 A or 16 A, and the next size up at 22 A or 25 A.
The common mistake is to size the drive on the motor’s kW. A 7.5 kW motor with a 0.82 power factor draws 13.5 A, and a drive rated at 16 A is right, while a 7.5 kW drive rated at only 12.6 A is too small.
Size one step up if the spindle sees heavy intermittent cutting. A drive that is continuously loaded at 90 percent of its rating runs hot and derates. A drive at 70 percent of its rating is comfortable.
Check the motor’s service factor and duty
A spindle motor rated for S1 continuous duty can be run at full rated current all the time. A motor rated S6 (intermittent duty) can be run above its rated current for a limited period. The nameplate service factor tells you how much overload the motor can take, and a spindle drive is the one place where that factor matters, because a dull cutter produces a sudden load spike that a feed axis never sees.
As a working rule, allow the drive to deliver up to 150 percent of the motor’s rated current for 60 seconds. If the drive cannot, the spindle will trip on an overload during a heavy cut rather than simply slowing down.
Speed range
The spindle’s usable speed range is set by the motor’s base speed and by the drive’s frequency range. A 4-pole 1440 rpm motor on a 50 Hz supply has a synchronous speed of 1500 rpm and a base speed of about 1440 rpm. To go above that, the drive must supply a frequency above 50 Hz, and above roughly 55 to 60 Hz the motor’s torque falls, its cooling becomes inadequate, and its bearings run hotter. In practice a 415 V VFD is good to 60 to 70 Hz for a standard motor, giving 1800 to 2100 rpm, which is enough for most cutting work with a gearbox or with a higher base speed motor.
For a spindle that needs 6000 to 8000 rpm, the motor must be a 2-pole design rated for high speed, at 2900 rpm base, and the drive must be a 415 V unit capable of 100 to 120 Hz output. VFDs that can be programmed to 120 Hz output are specific models, and they cost more. Check this before ordering, because it is not a software setting you can change later.
Section summary. The sizing arithmetic is short and the numbers come off the nameplate. For a three phase system kVA = sqrt(3) x V x I x pf, which for a 7.5 kW, 415 V, 13.5 A, 0.82 power factor motor gives 7.96 kVA. The rule that follows is that the drive’s rated output current must be at least the motor’s rated current, and the common mistake is to size on the kW and end up with a drive that is 12.6 A where 16 A is needed.
A spindle vfd selection on a 415 V three phase supply is the normal choice for a CNC spindle in India, and the sizing arithmetic is where that decision is justified.
3. Cabling and Grounding: Where the Faults Actually Come From
On a retrofit, the majority of the mysterious spindle faults are cabling faults. They present as intermittent trips, as the spindle that will not start after the machine has been warm for an hour, or as a machine that trips when the coolant pump starts.
The motor cable
Use a screened motor cable. Not a general-purpose rubber cable. A shielded motor cable with a shield that is a continuous foil or braid, rated for VFD output with a capacitance suitable for a high carrier frequency.
Both ends of the shield must be earthed. This is the case for VFD output cables, where the shield carries the common-mode current that the drive injects into the motor cable. A shield earthed at one end only leaves the other end floating and the common-mode current finds another path.
Keep the shield short at the drive. Use a 360-degree EMC gland rather than a single pigtail to a PE stud. A pigtail connection is measurably worse than a full clamp.
Separation
The VFD output cable is the noisiest cable on the machine. Rules that hold:
Keep the motor cable at least 200 mm from encoder feedback cables and from any signal cable, and never parallel with them for more than a short distance.
If they must cross, cross at right angles, never parallel.
Route the motor cable and the encoder cable in separate trays, and separate them from the cabinet mains wiring.
Do not run the motor cable in the same conduit as the thermocouple or the encoder cable, no matter how convenient it is.
Earth straps
This is where most Indian installations are wrong. The earth strap between the drive and the cabinet is often a 2 m length of 4 mm^2 wire, because that is what was in the box.
Use a short wide braided copper strap, 20 to 25 mm wide, between each drive and the cabinet earth bar. The impedance of a strap is proportional to its length and inversely proportional to its width, so a 0.3 m wide strap has roughly a fifteenth of the impedance of a 2 m wire of the same cross-section. In an installation where the fault is a high-frequency common-mode issue, the impedance of the earth path is what decides whether the noise stays inside the cabinet.
Then the cabinet to the plant earth: one dedicated conductor, as short as possible, sized to the highest earth fault current in the installation. And the cabinet door bonded with a strap, because a door is a hinged conductor and its bond is the first thing to be forgotten.
The motor as a noise source
The motor is part of the circuit. A 415 V motor on a VFD produces bearing currents, which come from the common-mode voltage on the shaft. Two consequences:
Insulated bearings or a shaft earth ring on any spindle above about 5 kW. A shaft earth ring is a carbon brush on the shaft end that grounds the shaft, and it costs very little compared with a bearing failure.
Do not use a standard VFD motor. If the existing spindle motor is an ordinary 415 V motor, add an output reactor between the drive and the motor. An output reactor, typically 2 to 5 percent impedance, reduces the dV/dt at the motor and therefore the bearing current. It also reduces the motor’s noise and the cable’s electromagnetic field, and it costs a small fraction of the drive.
Section summary. The majority of the mysterious spindle faults are cabling faults, and they present as intermittent trips or as a machine that faults when the coolant pump starts. The rules in spindle vfd selection are: a screened VFD-rated motor cable earthed at both ends with a 360-degree gland, at least 200 mm of separation from encoder cables, and short wide braided earth straps rather than the 2 m of 4 mm^2 wire that is usually what is in the box.
A 22 A drive for a 13.5 A motor is not overkill, it is the margin that lets the spindle survive a dull cutter for a few seconds instead of tripping instantly.
4. Parameters: Tell the Drive What Motor It Has
A VFD that has not been given the motor’s nameplate data will run, badly. This is the most common cause of a spindle that will not hold speed, that trips on overload, or that overheats the motor.
The mandatory parameters
Parameter
Value to enter
Consequence of getting it wrong
Rated voltage
415 V
The VFD will not produce the full flux. The motor runs with less torque than it should and the current goes up for the same load.
Rated frequency
50 Hz
The base frequency is wrong, so the motor’s speed-voltage relationship is wrong.
Rated current
13.5 A
Overcurrent protection trips at the wrong point, either too sensitive or not sensitive enough.
Rated speed
1440 rpm
The drive’s slip compensation and its speed display are wrong, so a commanded 1500 rpm does not give 1500 rpm.
Rated power
7.5 kW
Used to pre-set the acceleration ramps and the current limits.
Auto-tune
Rotating auto-tune
Without it, the drive’s current model is a guess and the slip compensation is wrong.
Auto-tune and why it must be rotating
Auto-tune measures the motor’s parameters, including its stator resistance, the magnetising current and the leakage inductance. A static (non-rotating) auto-tune gives most of this but cannot measure the rotor parameters. A rotating auto-tune runs the motor at a low speed with the shaft uncoupled, and it needs the machine’s drive train disconnected or the coupling removed, because the tuning applies a small alternating torque and the machine must be free to move.
On a retrofit with a gearbelt or a coupling, either uncouple it for the tuning or accept the static tuning and correct the slip manually. The symptom of bad slip compensation is a spindle whose actual speed changes with the load while the display shows a constant commanded speed.
The acceleration and deceleration ramps
This is where the machine’s behaviour is set, and it is the parameter most often left at the factory default.
Acceleration time. The default of 10 s from 0 to 50 Hz is very conservative for a CNC spindle. A spindle that takes 4 s to reach speed feels sluggish and the operator will find a way around it, usually by overriding the parameter.
But the ramp has to match the mechanics. The deceleration ramp should be set so the regenerative energy does not overvoltage the DC bus. The energy returned to the bus during deceleration is approximately E = 0.5 x J x omega^2. For a spindle with a total rotating inertia of 0.5 kg m^2 at 3000 rpm (314 rad/s), E = 0.5 x 0.5 x 98696 = 24,674 J, or 24.7 kJ. If the drive has no braking resistor, that energy has to be dissipated in the drive’s internal resistor, and the DC bus voltage rises. A drive with a braking chopper and an external resistor handles it cleanly.
Set the deceleration ramp no faster than the mechanical system can take. On a lathe with a big chuck, a very fast deceleration can put a shock load into the spindle bearings, which is exactly what the spindle rebuild guide warns against.
Current limit and overload protection
Set the drive’s current limit at 110 to 150 percent of the motor’s rated current, and set the electronic thermal protection to match the motor’s actual duty. A drive with the current limit set too low will trip on a heavy cut; set too high, it will let the motor burn. The correct setting is the motor’s rated current for continuous operation, with the overload capability of the drive’s own IGBTs as the headroom.
Carrier frequency
The carrier frequency is the switching frequency of the drive’s output transistors. Higher is smoother and quieter, and lower is more efficient with less radio-frequency emission and less motor heating.
For a machine with sensitive analogue signals near the spindle, a lower carrier frequency of 2 to 4 kHz reduces the electromagnetic noise.
For a spindle that should sound smooth, 8 to 16 kHz is better, at the cost of more heating in the drive and in the motor.
Use the shielded cable and the output reactor rather than lowering the carrier frequency, if the machine can take it. A reactor of 3 to 5 percent impedance also reduces the motor’s dV/dt, which prolongs the motor’s insulation life, and that matters on a retrofit where the original motor cable is 20 years old.
Section summary. A drive that has not been given the motor’s nameplate data will run, badly, and that is the most common cause of a spindle that will not hold speed or trips on overload. The mandatory entries in spindle vfd selection are rated voltage, frequency, current, speed and power, plus a rotating auto-tune with the drive train uncoupled. The symptom of bad slip compensation is a spindle whose real speed changes with the load while the display shows a constant commanded speed.
The earthing and shielding in spindle vfd selection is not paperwork, it is the difference between a machine that runs for ten years and one that is chasing noise faults every month.
5. Tuning on the Machine
With the parameters set, tune in a fixed order and record what you find.
Step 1: no load
Run the spindle through its whole speed range with no load. Listen. A healthy spindle at speed sounds like a smooth hum that rises in pitch with speed. Things to listen for:
A beat or growl at one particular speed. Usually a bearing defect, sometimes the gear mesh if the spindle has a gearbox, and sometimes a resonance of the spindle housing. Note the speed and check whether it occurs at a specific frequency.
A whine that rises and falls. Often the drive, not the spindle.
A change in sound at the top of the speed range. Above base speed, the motor runs into its power-limited region and the sound changes. This is normal, and it is where the motor’s torque is falling away.
Step 2: check the speed accuracy
Command 1000 rpm and check with a tachometer or with the machine’s own spindle feedback if it has any. Then repeat at 2000, 4000 and at maximum. If the commanded speed and the actual speed differ by more than 0.5 percent, the slip compensation is wrong. Re-run the rotating auto-tune.
On a CNC where the control commands the VFD through an analogue 0 to 10 V signal, there is a second scaling step: the controller’s spindle speed is a command in rpm, and the VFD’s analogue reference is a fraction of the maximum frequency. Get the scaling wrong and the spindle runs at the wrong speed with no error message. Test it by commanding 1000 rpm and measuring. The scaling rules and the VFD interface options are in the LinuxCNC hardware guide.
Step 3: load test
Cut a test workpiece in the real material, at the real cutting condition. Watch the current. This is where the diagnostic power of the current reading is.
Current behaviour
What it means
Steady, low, proportional to the cut
Normal. The spindle is matched to the work.
Steady but high, above 70 percent of rated
The spindle is undersized for the job, or the cut is too aggressive, or the belt or the tool is worn.
Rises steadily during a constant cut
A dull tool. The cutting force is climbing and the motor is loading up. This is the normal way a spindle load behaves.
Spikes at a fixed speed, repeatedly
A mechanical fault. A chipped bearing, a damaged tool, or a chipped cutter tooth passing one per revolution.
Oscillates, hunting
Speed instability. The drive’s slip compensation or its speed loop needs work, or the load is fluctuating.
Drops when the cut starts, recovers
The drive is at its current limit and is doing a slip-and-recover, which is a form of hunting.
Step 4: check the hunting
Hunting is a speed oscillation, and it has three likely causes in order of probability:
Speed loop gains too high. The drive’s speed loop is chasing small load changes. Reduce the speed loop gain, or check that the auto-tune was done correctly.
Mechanical resonance. The spindle or its mounting is resonating. It appears at one speed and disappears elsewhere. Find that speed and check whether it corresponds to the spindle’s natural frequency.
Supply voltage fluctuation. The drive’s DC bus is riding on the supply. Check the supply voltage at the drive under load, and check the input rectifier’s DC bus voltage in the drive diagnostics.
Step 5: the thermal test
Run the spindle at its production cycle for 30 minutes and check the motor’s temperature. The motor’s temperature rise should stay within what the motor’s insulation class allows. A rise of more than 80 degC above ambient indicates the drive is overloading the motor, that the cooling is inadequate, or that the bearings are dragging.
Also measure the spindle’s nose temperature. A spindle that is 20 degC hotter at the nose than at the rear housing is a spindle with a front bearing problem, and that is the finding that justifies a rebuild. The bearing and preload procedure is in the spindle rebuild guide.
Section summary. Tuning is a fixed order and the current reading is the diagnostic instrument most shops never use. The table in spindle vfd selection maps each current behaviour to its cause, and the distinction that matters most is a current that rises steadily during a constant cut, which is a dull tool, against a current that spikes repeatedly at a fixed speed, which is a mechanical fault. Hunting has three causes in order of probability: speed loop gains, mechanical resonance, and supply voltage fluctuation.
The nameplate values in spindle vfd selection have to come off the motor, not out of memory, because the motor on the machine is rarely the motor you planned for.
6. The Mistakes That Cost Time
Using the existing spindle motor with a 220 V single phase supply. It works, and it is marginal. The DC bus at 220 V single phase rectified is about 310 V, and the back-EMF at high speed approaches it, so the spindle loses torque at the top of its range. This is the reason many retrofit spindoles will not hold speed at the top.
Not earthing the cabinet properly. Symptom: the spindle trips or the control resets when the coolant pump or the spindle’s own contactor operates.
Using the motor’s rated frequency as the maximum frequency. The spindle then cannot go above base speed, and the operator complains that the machine is slow.
Skipping the rotating auto-tune. Symptom: the actual speed does not match the commanded speed, and the display shows the commanded value, so the fault is invisible until the operator measures it with a tachometer.
Leaving the factory defaults on the carrier frequency and the acceleration ramp. Symptom: the spindle is noisy and slow, and the noise is blamed on the bearings.
Not writing the parameter values down. Every drive replacement then becomes a guessing exercise, and the tuning is lost. Record the parameters, the auto-tune results and the test dates in the machine’s documentation folder. The full documentation discipline is in the parent retrofit guide, and the pricing of the spindle package is in the CNC retrofit cost calculator.
Section summary. The mistakes in this section are all cheap to avoid and expensive to discover, and they are the ones that get blamed on the wrong component. Using the existing spindle motor on a 220 V single phase supply loses torque at the top of the range, skipping the rotating auto-tune makes the fault invisible until someone measures with a tachometer, and not writing the parameters down turns every drive replacement into a guessing exercise. spindle vfd selection is finished when the values are in the machine’s documentation folder.
The current trend during a cut is the most useful diagnostic in spindle vfd selection, and it costs nothing once the drive is set up to display it.
Size the drive with kVA = sqrt(3) x V x I x pf, and pick the next standard size up from the motor’s full load current.
A 415 V three phase spindle VFD is the normal choice for CNC servos because a 220 V single phase supply leaves no margin for the back-EMF at speed.
Shielded motor cable, bonded at the drive end, with a short wide earth strap from the drive to the cabinet, eliminates most of the mystery faults.
Set the VFD motor nameplate volts, hertz, current, speed and power before any tuning; an unnamed motor makes the drive guess and guess wrong.
Rising current during a cut means the spindle is loaded; a current spike at a fixed speed means a mechanical fault such as a dull cutter or a binding bearing.